SAS 01

HIGH GLOSS SURFACE COATING FOR FLOORING

PRODUCT INFORMATION

An innovative technology is brought with the new Alpha SAS 01, a single component, clear coating based on hybrid polymer technology. The coating improves and enhances the natural appearance of the flooring and provides a polished finish with anti-staining properties.

It can be used to protect concrete and cementitious floors to retain their value and appearance for years to come and protect against abrasion and scratching.

Alpha SAS 01 is a ready to use product that does not contain isocyanates, epoxy resin or amines typically used in traditional floor coating systems.

KEY INFORMATION

  • Excellent anti-staining properties

  • Abrasion and scratch resistance

  • Shiny appearance, polish optional

  • UV and Chemical resistance

  • Isocyanate  & solvent free

  • Low coat weight

  • Can be applied at low temperatures and in high humidity conditions

  • Anti-slip

TYPICAL APPLICATIONS

Alpha SAS 01 is suitable for the following applications:

 

  • For new or old concrete floor treatment
  • Cementitious flooring
  • Paving stones, clinker, bricks and natural stone.
  • For polishing surfaces
  • For decorative flooring in galleries, museums, shopping malls
  • Ideal for schools and hospitals as it contains no isocyanates or bisphenol epoxy.

PRODUCT CHARACTERISTICS

The following technical information and data should be considered representative or typical only. Therefore, the information should not be used for specification purposes

* This time is shorter when temperature and relative humidity are higher.

HANDLING & APPLICATIONS

The general application information presented here is based upon typical conditions determined by Alpha Adhesives & Sealants Limited testing. Our recommendations on the use of this product are based on methods believed to be reliable. It is advised that users conduct their own tests to determine the suitability of the product for their specific application.

All substrate surfaces should be cleaned of any dust, grit, loose material, wax, grease and oil.

Once the container of Alpha SAS01 has been opened, a thin, crystallized skin will form on top. Prior to reuse it may be necessary to remove the layer. The uncured product  underneath the layer will still be suitable for use.

Do not stir the product before use as this will introduce moisture into the bulk liquid and reduce the shelf life of the product.

As this is a moisture curing product, it is recommended that small amounts of material is decanted into a suitable tray. The container should be closed after use. Do not pour excess material back in to the original container.

The material should be applied with a short-hair roller to avoid formation of bubbles during application.

SAS 01 should be applied in two coats. The first coat strengthens the floor.  The second produces a homogeneous surface that increases scratch and abrasion resistance, and makes the floor polishable.

Each coat takes approximately 12—24 hours to cure dependent on temperature and relative humidity of the location.

For best results, it is recommended that no pressure is applied when coating with a roller as this could produce bubbles and affect the final appearance.

Each coat should be a very thin layer over the flooring surface. The consumption for the first coat should be approximately 50 grams per square metre. It is recommended that the second coat should be applied as a thinner coat than the first, at a consumption of approximately 20-50 grams per square metre.

The rate of cure is dependent on the ambient environmental conditions and the humidity content of the floor surface.

No traffic should be allowed on the treated surface within 24 hours after the second coat has applied. After 24 hours, foot traffic can be permitted.

Clean tools immediately after use with T559 (TF). Clean hands with a proprietary hand cleaner.

HEALTHY & SAFETY INFORMATION

Alpha SAS 01 is classified as hazardous according to Directive EC 1272/2008. Please refer to the Alpha SAS 01 Safety Data Sheet for further health & safety information.

STORAGE

Alpha SAS 01 should be stored in its original container, in dry conditions, properly closed and at temperatures between 5°C and 20°C. Alpha SAS 01 will keep satisfactorily for up to 12 months from date of manufacture if stored according to the recommended conditions.

PRODUCT AVAILABILITY

Product Reference
Pack Size
Container
Box Quantity
Alpha SAS 01
25 L
Drum
1
Alpha SAS 01
205 L
Drum
1
Alpha SAS 01
1000 L
IBC
1

ISSUE : 4

January 2019